1442 Results
View results:
Sort by:
Add-ons for Timber Structures
Which Dlubal software products do you recommend for the structural analysis and design of timber structures in particular?
Resetting Display Settings to Dlubal Standard
How do I reset the display settings to default?
Comparative Analysis for RANS, URANS, and DDES Turbulence Models
What is the difference between the RANS, URANS, and DDES turbulence models?
Double-Sided Stiffening (Splice)
How can I model a timber beam with stiffening on both sides? (splice)
Load Extension Isotropic Masonry | Plastic
Is it possible to influence the transverse distribution of a load in the case of the Isotropic | Masonry | Plastic material model?
Plastic Hinges
How do I define a plastic hinge in RFEM 6?
Interface RFEM 6 / RSTAB 9 – IDEA StatiCa
How can I exchange data between RFEM 6 / RSTAB 9 and IDEA StatiCa?
Advantages of CFD Simulation
What are the advantages of CFD simulation compared to conventional experimental tests?
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Add-ons for Steel Structures
I process steel structures. Which products do you recommend for this area?
State of Development of Beam Panel
What is the current state of development of the "beam panel" element for modeling timber frame walls?
Not Valid/Deactivated Punching Nodes
In the table of the objects to be designed in the Concrete Design add-on, punching nodes are listed in the not valid/deactivated column, although I have defined them as punching nodes. How can I fix this?
Area Loads on Members via Cells
How can I generate an area load on members via cells in RFEM 6 or RSTAB 9?
Setting of I-Beam Flange Support for Design in Structure Stability Add-on
In the Steel Design add-on, I have set the boundary conditions in such a way that the I-beam flange is restrained against the horizontal displacement. I then calculated the critical load factors using the Structure Stability add-on, but with no effect on the critical load factor value. What is the reason for this?
Graphic Templates for Printing Reinforcement Layout
How can I use graphic templates for multi printing of a reinforcement?
Activating Steel Fiber Concrete Design in "Concrete Design" Add-on
How can I activate the design with steel fiber-reinforced concrete in the "Concrete Design" add-on for RFEM 6?
Unit Stresses
Can I estimate which minimum cross-sections I should use before starting to design my model?
Member Nonlinearity
Is it possible to define member nonlinearities for beam members?
For example, can I define a member that absorbs all internal forces, except for the compressive axial forces?
Pipe as Shear Key in RF-/JOINTS Steel – Column Base Add-on Module
How do I define a pipe as a shear key in RF‑/JOINTS Steel – Column Base add-on module?
Incorrect Material or Cross-Section Conversion in Revit or Tekla
I get an incorrect conversion in Tekla/Revit when using regular expressions in the conversion table.
Steady-State or Transient Simulation for Parapet in RWIND
What is the most accurate CFD method for the wind simulation of parapets?
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM